Alchatek Blog

The terms hydrophobic and hydrophilic may not mean anything to the average person. But, to a contractor, these terms can mean a world of difference. Hydro means water while phobic means “to fear” and philic means “to love”. Alchatek offers both hydrophobic and hydrophilic polyurethanes, so it is important to be aware of the differences between the two types.  

Hydrophobic Polyurethanes

Hydrophobic polyurethanes naturally repel water (similar to the way oil would repel water and stay separate if you were trying to mix them in a glass). These products push water out of the area in question as they expand. Hydrophobics are used with catalysts which allow you to adjust the set time. They also have zero shrinkage after curing.

Check out these hydrophobic polyurethanes:

• Spetec PUR HighFoamer 
• Spetec PUR F400
• Spetec PUR H100 
• Spetec PUR H200 
• AP Fill 420
• AP Deep Lift® 420
• AP Lift 430
• AP Lift 435
• AP Lift 440
• AP Lift 475
• AP Soil 600 
• AP Fill 700
  
• AP Fill 720

Hydrophilic Polyurethanes

Hydrophilic polyurethanes naturally mix with water before curing (similar to the way gin and tonic mix thoroughly in a glass). This characteristic allows for a very strong chemical and mechanical bond, as water helps pull the material into the pores of the concrete. These products do not require a catalyst. You can pump them straight out of the pail.

Check out these hydrophilic polyurethanes:

• Spetec PUR GT350
• Spetec PUR GT380
• Spetec PUR GT500

Don't Oversimplify These Concepts

Don't get caught in the trap of oversimplifying hydrophilic vs. hydrophobic.  There are varying degrees of each (see chart below for more information on how this is measured).  

Some hydrophilic materials will keep absorbing water (10-15 times their original volume).  Others (such as Spetec PUR GT500) only absorb as much water as is necessary for their reaction and then they reject the rest.  Yes, hydrophilic gels will shrink like crazy in the absence of water, but Spetec PUR GT500 won't.  It is completely safe to use in a dry environment.

Want more information on Alchatek products?

Carrington Woods Lake Dam is located in Baldwin County, Georgia. A consulting firm collaborating with a general contractor called in geotech specialists Atlas Structural to stabilize an abandoned below-grade culvert pipe that had deteriorated over time. The pipe ran underneath a spillway. With supporting soil migrating into it, its unstable condition threatened the integrity of the structure.

Powerful Polymer

The technicians chose single-component AP FIll 720 for the job. The deteriorating pipe was 100 feet long, and due to the circumstances at the site, grouting could only be done from one end. Getting a two-component foam 100 feet up a pipe before it cured would have been impossible. AP Fill 720, featuring a very flexible set time adjustment range with the catalyst, allows technicians to pump the material for great distances before it starts to react and cure.

Painless Procedure

AP Fill 720 does not have to be heated and only needs moisture for reaction. The crew had two electric injection pumps, one pumping AP Fill 720 with an accelerator and the other pumping water. They had 150-foot lines on each pump. Both pump lines were run through a 100-foot PVC tube. The technicians used a video camera, mounted five feet back from the end of the PVC tube, to monitor the fill. The crew pumped both water and poly in unison for a good reaction. As the pipe filled up, they slowly withdrew the PVC and continued pumping until the pipe was full. The process basically consisted of pumping, extracting the tube a foot, and repeating - until the entire 18" x 100' pipe was filled.

Rapid Result

The deteriorated pipe was completely filled and stabilized. Soil migration was stopped and the threat to the structure of the spillway above was eliminated. This job was completed in only three hours. Complete removal or filling with concrete would have taken days. In addition, concrete does not expand, so a 100% fill would have been impossible. AP Fill 720 expanded to fill 100% of the pipe. The consulting engineer and general contractor were very happy with this result.

Want more information on geotech products and equipment?

When the residue of plants or animals is converted into soil, the process is known as decomposition. Bacteria, fungi, and worms break down this residue, taking nutrients from them and leaving the remaining portion. Organic molecules are broken down into simpler inorganic molecules. This biological process changes the makeup of the soil and can therefore lead to soil instability.

What are the causes of decomposition?

When soil has a high concentration of organic materials, the soil will naturally begin to decompose. Throughout this process of decomposition, the mass and form of these organic materials will change. Up to 90 percent of organic material will actually disappear over the course of the decomposition process, which means the mass of the soil will decrease substantially, reducing the quantity of available soil. The causes of decomposition can be broken into two main groups: manmade and natural. Trash pits or buried construction debris can cause manmade decomposition, while tree stumps and peat content can cause natural decomposition. 

What are the signs of decomposition?

Sinkholes, unstable soil, and low spots are all indications of soil decomposition. When soil begins to decompose and shift, it can compromise the integrity of buildings, foundations, and other manmade structures. 

How can decomposition be addressed?

In some cases, it is possible to dig up the cause of decomposition. For example, it might be possible to extricate a trash pit or old construction debris from the soil. However, in other cases, this simply isn’t feasible. You can’t easily extricate a trash pit after you have already built on top of it. If removal isn’t an option, the best solution is to envelop the area with polyurethane soil stabilization material. This process is known as encapsulation, and it essentially works to compact the area and reduce the amount of oxygen and water that can get to it, thereby helping to slow decomposition.

Want in-depth info on soil stabilization procedures and products?

What is freezing and thawing?

As the name suggests, a freezing and thawing cycle refers to a natural phenomenon in which soil freezes in cold weather and then thaws out again once the temperature warms up. Freezing and thawing in northern climates is good news for farmers, as it helps to loosen up the soil and reduce compaction, which makes it easier for crop roots to grow. However, for construction engineers and contractors, this process can prove to be incredibly problematic, especially if they are building on fine-grained soils with silt or clay factions, which are more prone to freezing and thawing.

What are the problems associated with freezing and thawing?

Essentially, freezing and thawing cycles accelerate soil instability. Soil with pores containing small particles of frozen water is known as permafrost. Building on permafrost is fine, as long as the soil stays frozen, but things become problematic once the permafrost begins to thaw. Freezing and thawing of permafrost cause soil to become soft and less compact. Subsequently, this causes structures, such as roadways, railways, foundations, and pipeline supports, to sink. Obviously, this can cause major headaches.

How can the problem of freezing and thawing be mitigated?

Alchatek soil stabilization products can be used to compact the ground and displace water particles in the soil pores. Depending on the soil type, this could prevent frost heave, resulting in a stronger, more consistent base to build on.

Want in-depth info on soil stabilization procedures and products?

Many types of infrastructure, including roads, bridges, and buildings, depend on compacted soil in order to stay in place. Therefore, in order for these structures to last, a specific degree of compaction must be achieved. When soil does not adequately compact, the problem is known as poor compaction, and that can lead to more serious issues. Concrete repair contractors always need to be on the lookout for signs of poor compaction which include settling slabs, cracking foundations, and dips in roadways and railroads.

What causes poor soil compaction?

There are a variety of causes of poor soil compaction. However, much of it boils down to soil texture and soil properties. Some soils are more prone to compaction than others. Excess soil salt content, high clay fraction soils, low pH soils, and soils with high water content tend to compact less favorably. It should also be noted that decisions made by construction contractors and their teams can also influence soil compaction. For example, failure to select proper compaction equipment or compaction materials can contribute to poor compaction. Furthermore, some areas are more prone to poor compaction than others, such as portions of soil set against a foundation.

How can poor soil compaction be corrected?

Luckily, poor compaction can be corrected. The solution is to strengthen the soil until it is properly compacted. As mentioned in the previous post, voids can be filled, soil consolidated, and water migration halted with Alchatek soil stabilization products. Once the bearing capacity of the soil has been increased with this process, then the structure can be lifted if necessary.

Want in-depth info on soil stabilization procedures and products?

What is erosion?

In geological terms, erosion can be defined as an exogenic process that moves a portion of the earth’s crust from one location to another. This includes a range of different processes, including water flow, wind, and even human action, that move dirt, soil, rock, etc. They are called exogenic processes because they originate outside of the earth’s crust, or externally. In more practical terms, erosion can best be described as the way in which the earth is worn away by water, wind, or ice. So when a river carves a canyon out of stone (such as when the Colorado River carved out the Grand Canyon in Arizona over the course of so many years), that is an example of erosion. The formation of sand dunes by the wind moving across the desert is also an example of erosion, as are changes in rocks along a shoreline due to the constant thrashing of waves. 

Why does erosion cause unstable soil?

You’ve probably heard that erosion is dangerous because it causes unstable soil. It is important to remember that the consequences of erosion can potentially be dramatic, causing landslides and structural damage. After investing money in the construction of a building, the last thing you want is for unstable soil to put the whole project at risk. 

How can erosion be repaired?

Voids can be filled, soil consolidated, and water migration halted with Alchatek soil stabilization products. Once the bearing capacity of the soil has been increased with this process, then the structure can be lifted if necessary.

Want in-depth info on soil stabilization procedures and products?

Unstable soil can be defined as soil that will not stay in place on its own and therefore requires extra support. It should be noted that unstable soil can threaten the stability, security, and safety of infrastructure and can damage, degrade, and even destroy a number of structures, such as buildings, bridges, and roads.

Let's look at the four main causes of unstable soil...

Erosion

Erosion refers to processes in which external elements (wind, water, etc.) remove soil or rock from a certain location and transport it to another location. There are a variety of different erosion types, including river and gull erosion, wind erosion, and erosion attributed to human activity. Erosion ultimately destabilizes soil and can lead to landslides and sinkholes.

Poor Compaction

One of the most common causes of unstable soil is poor compaction. In some cases, certain types of soil are simply very loose and subsequently not compact. The cause of this is typically an imbalance of mineral pieces, organic matter, air, and water. For example, clay soil with very high moisture content will inevitably become unstable, as it will be incredibly difficult to compact. Similarly, soils with high sand content will be difficult to compact.

Freeze/Thaw

Processes of freezing and thawing essentially accelerate erosion processes. Cold weather freezes moisture trapped in tiny cracks. When this water freezes, it expands, subsequently pushing on the rocks and breaking them into smaller pieces. As processes of freezing and thawing continue, rock and sediment are continually broken down.

Decomposition

When soils contain a high concentration of organic materials, such as topsoil and plant matter, they will decompose, subsequently causing them to become unstable. This is because organic materials rapidly change form and mass as they decompose in the soil. In fact, up to 90 percent of organic material will disappear over the course of the decomposition process.

Fortunately, stability can be restored to soil with ultra-low viscosity polyurethane resins. Foaming and permeation polyurethanes can mitigate the damage done by processes of erosion, decomposition, freezing, and thawing, as well as help to rectify compaction problems. When it comes to unstable soil, you can’t afford to take a risk. Stable soil is crucial to maintaining secure structures.

Want in-depth info on soil stabilization procedures and products?

Raising Concrete with Confidence

When pumping a lightweight material beneath a slab, you need the confidence that it is strong enough for the application. How strong is strong enough? This is a commonly asked question by contractors that are new to slab jacking with polyurethane. Alchemy-Spetec structural foams only need to be as strong as dirt, but they're actually stronger than crystalline bedrock.

The Right Strengths for Concrete Lifting

Slab lifting foams are rated on density (weight per cubic feet) and compressive strength. This testing and rating are based on the foam in a free-rise state; the parts A and B are mixed together and allowed to expand freely. Our AP Lift 430 and AP Lift 475 structural lifting foams, for example, weigh 2.75 – 3.25 lbs (AP Lift 430) to 4.75 – 5 lbs (AP Lift 475) per cubic foot. But they have compressive strengths of 50 psi and 100 psi in a free-rise state. That's the equivalent of 7,200 to 14,000 lbs per square ft of support, just in a free-rise state.

Polyurethane Slab Jacking Compared to Clay and Bedrock

To put that into perspective, the National Home Builders Association and the International Building Code list stiff clay at 4,000 psf and crystalline bedrock as having 12,000 psf of load-bearing capacity. Consider the job site conditions where the foam will be injected into a confined area. Testing data in the lab shows that our lifting foams will increase in compressive strength: In a space confined 25% by volume there will be an increase of 31% in psi and in a space confined by 75% there will be a 79% increase in the psi.

Concrete Leveling for Any Job with the Right Foam

Today polyurethane concrete lifting foams are used to level airport slabs supporting jumbo jets, equipment and building slabs supporting tremendous loads, and even railway sleepers that support the heaviest freight trains. So don't let the word “foam” fool you. These resins cure to strengths beyond what is needed to support any structure.

Want in-depth info on slab lifting procedures and products?

If you're a leak seal contractor, you may be familiar with this situation: A property owner with leaking concrete calls you up and says, "Hey, everything is dry right now, so I want to get someone out here to go ahead and waterproof the structure."  Attempting a waterproofing job when the structure is completely dry is not recommended.

Let me give you an analogy. Let's say I hired you to paint a basement. And when you arrive, it's pitch black in that basement. No lights are available and you can't see anything. Can you still paint that basement? The answer is "yes", but when we turn the lights on, will I be happy with the job you've done? There's no way. It would be a terrible paint job.

Similarly, if someone is asking you to waterproof while it's dry, you are basically attempting to seal leaks while blind. You need to waterproof while water is present - not just to activate the grout, but to see where the grout needs to be. Let the leaks lead you to correct grout placement. You won't know for sure if the water is not present. If you attempt a leak seal job in a completely dry environment and then return when the water is present, you'll most likely find leaking cracks that you missed.

Moral of the story? Grout when it's wet.

Want more information on leak seal products and equipment?

The Alchatek app includes a Leak Seal Material Selection Guide and a Polyurethane Estimating Calculator.  The Leak Seal Product Selection guide asks you a series of Yes/No questions about your job and then provides product recommendations.  The Polyurethane Estimating Calculator takes the guesswork out of estimating material for Geotech and Leak Seal jobs. Here's a step-by-step guide...

Install the Alchatek App and Create an Account

1. Search the name Alchatek in your Apple App Store or Google Play Store to install the app. 

2. After installing the app, create an account by clicking "Sign Up" at the bottom and following the prompts.

Polyurethane Estimating Calculator (Estimate Material Quantities for Your Job)

1. Tap the three lines in the top left corner to display the application options. Choose Material Estimation Calculator, then choose Geotech (Slab Lifting & Void Fill) or Leak Seal for your job type.

2. Select the measuring system you want to use.

3. Fill out the required fields.

4. View the recommended material quantities.

Leak Seal Material Selection Guide (Choose a Leak Seal Product for Your Job)

1. Tap the three lines in the top left corner to display the application options. Choose Leak Seal Material Selection Guide.

2. Answer a series of Yes/No questions about your leak seal job.

3. Review the product recommendation screen (and/or click the Start Over button at the bottom to begin again).

Want more information on Alchatek products?